Gobal WebSites:

Clirik ultrafine grinding mill

Date:2014-04-08 11:07:48    From:    Click:

1. Product Description:

Clirik ultrafine grinding Mill integrates the functions of milling, classifying and drying. Compared with ball mill, Raymond mill and other grinding equipments, Clirik ultrafine grinding mill has the advantages of high efficiency, energy-saving, good grinding effect, good drying capacity, easy coarse and fine adjustment, even grain size, easily controlled chemical composition, low noise, less dust, less metal abrasion, easy operation, convenient replacement of wearing parts, easy system process, less covering area, good comprehensive benefits, and so on. Thus, Clirik ultrafine grinding mill draws great attention from powder processing industry and is widely used in the field of grinding calcite, electrolytic stone, talc, kaolin, manganese ore, rock phosphate, gypsum, zircon, silicon metal, etc.

2. Working Principle:

The motor drives the mill disc to rotate through speed reducer and drives the grind roller rotates through belt gear at the same time. The material falls into the center part of mill disc from the feed port and simulate the hot air enter the mill. Under the action of centrifugal force, the material moves to the mill edge, and is to be grinded by rolling and shearing when passing through the ring groove on the mill disc. The grinded material is blown up by high speed air from wind loop at the edge of mill disc. The large grains fall onto the mill disc and are grinded again. The material in the air stream passes through the classifier. The rotator makes the coarse grain fall onto the mill disc to be grinded again and the qualified fine grain come out of mill. And then the finished fine materials are collected in the powder collecting system. The fine materials with water content are dried by hot air and then achieve the required product moisture. The air is recycled and reused. During the circulation, the small surplus air is collected by the by-pass dust collector in this system with the lighter impurities, which forms a scientific and advanced process.

3. Features

1). Low running cost:

The milling efficiency is high and the power consumption is low. Compared with ball mills, Raymond mills and other milling machines, the power consumption of clirik ultrafine grinding mill decreases 40~50%. The abrasion is low, roll sleeve and liner has long service life by adopting special materials, which reduces the metallic pollution and running cost. External circulation device can be equipped to reduce power consumption further and improve product accuracy.

2). Low project implementation:

Compared with ball mill, Clirik ultrafine grinding mill covers 50% less area and project implementation decreases by 70%.Clirik ultrafine grinding mill integrates crushing, drying, milling, classifying and conveying, which makes the system simple and the project implementation low.

3). Easy and reliable operation:

Clirik ultrafine grinding mill is equipped with automatic control equipment, which can realize remote control. There is also a device which can prevent grind roller from contacting with liner directly and can avoid destructive vibration.

4). Convenient maintenance:

Sliding the frame during the maintenance on hydro-cylinder, which can replace roller sleeve and wear ring in a short time. The material of wear ring is 50SiMn.

5). Less environmental pollution:

There is low vibration and low noise for vertical milling machine. The whole system is under negative pressure, which avoids dust overflowing.

6). Reliable quality:

The material stays less time in the mills, which can easily test and control product size and chemical composition. This mill is equipped with high accuracy analyzer, which can classify the products from 325 meshes to 3000 meshes. The classifying accuracy is high, the cutting position is accurate and the product quality is reliable.

Technical data of Clirik ultrafine grinding mill:

Model HGM80 HGM90 HGM100 HGM100A HGM125
Ring Diameter(mm) 800 930 1035 1300
Ring Number(PCS) 3 3~4 3 4 4
Roller Number(PCS) 21 24~32 27 34~36 40~44
Main Shaft Speed(r.p.m.) 230~240 200~220 180~200 135~155
Input Size(mm) ≤20
Finished Size/um(mesh) 5-47(325~2500)
Capacity (t/h) 0.5-4.5 0.6-6.5 0.7-7 1-8.5 1.5-12
Outlet Size (L*W*H, m) 13.9*4*6.2 14.7*4.8*7.2 18*4.6*8.6 14*9*10.25
Motor Power(KW) 145-165 185-204 263 263-290 380-430



Note: This specification is just referencing, any changes are subject to the products.


Grinding mill-13.jpg


More info,please click www.stone-mills.com

or you can send your inquiry to www.sales@clirik.com

It would be our pleasure to serve for you.